Professional System-Level Control for CNC Manufacturing, Robotics and Automation
Site Search:
 



Please see the Tips and Suggestions for Leaving Comments below


For answers to your questions, please e-mail info@dynomotion.com

Comments (35)

Topic: Reviews
Sort
5/5 (32)
First < 1 2 3 4 > Last
Gravatar
Full StarFull StarFull StarFull StarFull Star
Federico de la Cruz (Argentina)
Amazing products! Bought a Kflop and Kanalog for a Mazak V-10 retrofit, no machine hardware update need. Uses original drives, tachogenerators and RESOLVERS for servo closed loop,resolver accuracy(electric)0.002 mm. Works perfect even with very complicated shapes and high speed. The servo tuning is very easy. I strongly recommend to use KMotionCNC, the trajectory planner works perfect. Anyone who needs help with similar machine, just send email: fdelacruzriz@gmail.com Very pleased with the ... Read More
30th May 2016 6:23pm
Gravatar
Full StarFull StarFull StarFull StarFull Star
Gary Styger (South Africa)
I am currently completing my post-graduate work and I constructed a 3-axis milling machine as part of the scope of work. I initially purchased a motion controller and stepper driver that was recommended to me. Initially it ran well and then the USB connection would disconnect and when re-connecting miss commands in the Gcode. There was no support for this product so I was stuck. I then did investigation and came across the Kflop and Kstep. I wrote numerous e-mails to Tom asking question after ... Read More
25th May 2016 1:07pm
Gravatar
Full StarFull StarFull StarFull StarFull Star
Jean-Luc Michaud (Canada)
I designed and built a 5-axis hot wire foam cutting machine for a project at school. I am a mechanical engineering student, so C-Code and motor control was obviously not my speciality. However, I still chose to buy the KFLOP and two KSTEPS, and I am extremely happy with my choice. The documentation on the website is very complete. Each time that I had a specific question, Tom answered to me within an hour with THE solution to my problem. The KSTEPS are running like magic. They produce almost ... Read More
31st December 2015 6:28pm
Gravatar
Full StarFull StarFull StarFull StarFull Star
Sergei
Best of the best product
3rd September 2015 2:08pm
Gravatar
Full StarFull StarFull StarFull StarFull Star
Cole Larson (US)
I replaced a Dynapath 10 on my Bridgeport mill with kflop+kanalog. The process went without a hitch over a month or so of weekends and the system is a joy to use. The machine is smoother, easier to program and much more accurate.

I can't comment on the support because I HAVEN'T HAD TO USE IT YET!!!!

This is the best product on the market today to use when replacing old CNC controllers!.
6th July 2015 9:37am
Gravatar
Full StarFull StarFull StarFull StarFull Star
Henk Sterk (Malaysia)
Nothing but praise..(user for 3 years) I was looking to build a cnc machine for a while, but couldn't decide which direction to go, so started buying components on ebay like servo drives and controler even bought the software (Mach III). Lucky enough I found a second hand EDM machine from 1995 (good for cnc milling rebuild), the control panel has gone up in smoke (so the price was very cheap), it has 3 Heinenhain glass scales and C3 ball screws. So I started to get very excited about the ... Read More
6th April 2015 8:52am
Gravatar
Full StarFull StarFull StarFull StarFull Star
Brian Williams (US)
I am using the KFLOP + SnapAmp in my SuperMax CNC. Been running it for about 2 years flawlessly. Ran into an issue that ended up being the USB cable but Dynomotion was there to help me figure it out. The support folks at Dynomotion are incredible. They are always there to help, superb! Thanks!
12th March 2015 1:16pm
Gravatar
Full StarFull StarFull StarFull StarFull Star
Troy (US)
After my first retrofit of a CNC knee mill with steppers and glass scales(2008 time frame),i was searching for a way to close the loop. Came across the KFLOP board and was amazed how well the stepper closed loop works. The support from Tom is the best i have ever seen...when a wall appears he stomps it down flat and keeps going. I have said this about very few people. Currently using a KFLOP on my mill/drill stepper with glass scales at home. Here is a link to it, the page is a little out of ... Read More
4th November 2014 5:31pm
Gravatar
Full StarFull StarFull StarFull StarFull Star
Peter Cats (Holland)
We use the Kflop cards for different projects, running 7 different programs at the same time on one card helped a lot in our projects. The support is ok, documentation about some programming aspects could be a little better in some cases. But it is a great product.
24th October 2014 10:24am
First < 1 2 3 4 > Last
Page 3 of 4

Add Comment

* Required information
(never displayed)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Numeric Link Email Image Video
 
2000
 
Notify me of new comments via email.
 
Remember my form inputs on this computer.
 
I have read and understand the privacy policy. *
 



Tips and Suggestions for Leaving Comments:

  • Tell us which products you have and are reviewing.
  • Briefly describe your application.
  • Tell us how long you have used Dynomotion products.
  • Mention something about your own experience.
  • Provide links to any videos and pictures that will help others understand your application and setup.
  • Your e-mail address is kept confidential and never displayed. It is only used for notifications about your comment and for service issues.
  • We have a mixed audience, please keep your comments professional. Dynomotion reserves the right to censor reviews for offensive content.
  • If you have negative comments to leave, please first give Dynomotion the professional courtesy to correct any issues you may be experiencing. E-mail support@dynomotion.com.










Copyright © Dynomotion, Inc.