RTCP 5 axis machine

Moderators: TomKerekes, dynomotion

User avatar
TomKerekes
Posts: 2527
Joined: Mon Dec 04, 2017 1:49 am

Re: RTCP 5 axis machine

Post by TomKerekes » Sun Jan 05, 2020 6:14 pm

Hi Igor,
yes I know mach3 does not support rtsp. settings cited as an example. here is the official site please see there. http://leadshine.com/productdetail.aspx ... =ES-DH2306
That seems to be a different model number than you said previously. But yes that drive should work in step/direction mode.


Unblocking doesn 't work, KMotion doesn 't work.
Strange. I tried it on 2 computers without problems. Is your download the same size as shown above? Are you running any antivirus? What exactly are you doing? What happens?
Regards,

Tom Kerekes
Dynomotion, Inc.

Igor
Posts: 60
Joined: Wed Dec 25, 2019 11:37 am

Re: RTCP 5 axis machine

Post by Igor » Sun Jan 05, 2020 6:33 pm

windovs10-1809. When click on the window KmotionCNC opens and immediately collapses anti-virus only in the package windows/ tomorrow I will go to the mail to receive your fee))

Igor
Posts: 60
Joined: Wed Dec 25, 2019 11:37 am

Re: RTCP 5 axis machine

Post by Igor » Fri Jan 10, 2020 7:53 am

Good afternoon Tom, I am in trouble, and I cannot apply your recommendations. Any solution to this problem?
I made changes to the postprocessor for the PowerMill program, the code looks like this
. This will work fully when creating a standard profile setup? when simulating in KMotionsCNC - the trajectory is displayed correctly
%
N1 G90
N2 G0 Z50.
N3 X45.5 Y0 A0 B0
N4 S1500 M3
N5 G0 Z50.
N6 X45.5 Y0 A0 B0
N7 G1 X45.508 Y-.406 Z50. A.324 B-.135 F3000
N8 X45.517 Y-.812 A.649 B-.269
N9 X45.525 Y-1.218 A.974 B-.404
N10 X45.534 Y-1.624 A1.3 B-.539
N11 X45.542 Y-2.029 A1.626 B-.675
N12 X45.55 Y-2.435 A1.952 B-.81
N13 X45.559 Y-2.84 A2.279 B-.946
N14 X45.567 Y-3.245 A2.607 B-1.082
N15 X45.576 Y-3.649 A2.935 B-1.218
N16 X45.584 Y-4.054 A3.263 B-1.354
N17 X45.592 Y-4.459 A3.592 B-1.49
N18 X45.601 Y-4.863 A3.922 B-1.626
N19 X45.609 Y-5.267 A4.251 B-1.763
N20 X45.617 Y-5.671 A4.581 B-1.899
N21 X45.626 Y-6.075 A4.911 B-2.036
N22 X45.634 Y-6.479 A5.242 B-2.172
N23 X45.643 Y-6.883 A5.573 B-2.309
N24 X45.651 Y-7.287 A5.904 B-2.446
N25 X45.659 Y-7.69 A6.236 B-2.582
N26 X45.668 Y-8.094 A6.568 B-2.719
N27 X45.676 Y-8.497 A6.9 B-2.855
N28 X45.684 Y-8.901 A7.232 B-2.992

This trajectory without Activatsii RTCP - PowerMill postprocessor has a non-coretic appearance
%
N1 G90
N2 G0 Z50.
N3 X45.5 Y0 A0 B0
N4 S1500 M3
N5 G0 Z50.
N6 X45.5 Y0 A0 B0
N7 G1 X45.157 Y-.689 Z49.996 A.324 B-.135 F3000
N8 X44.814 Y-1.378 Z49.986 A.649 B-.269
N9 X44.47 Y-2.068 Z49.968 A.974 B-.404
N10 X44.126 Y-2.757 Z49.944 A1.3 B-.539
N11 X43.781 Y-3.447 Z49.912 A1.626 B-.675
N12 X43.436 Y-4.137 Z49.873 A1.952 B-.81
N13 X43.09 Y-4.826 Z49.827 A2.279 B-.946
Attachments
CNC1.PNG
CNC.PNG

Igor
Posts: 60
Joined: Wed Dec 25, 2019 11:37 am

Re: RTCP 5 axis machine

Post by Igor » Fri Jan 10, 2020 8:13 am

I also have another problem when turning on flashing these pinas, and in some I can 't change the value, what is the problem, the controller is not correct?
Attachments
CNC2.PNG

User avatar
TomKerekes
Posts: 2527
Joined: Mon Dec 04, 2017 1:49 am

Re: RTCP 5 axis machine

Post by TomKerekes » Fri Jan 10, 2020 6:45 pm

Hi Igor,

Let's first focus on getting the Patch to work.

#1 - what Version of KMotion are you running? (Right click KMotionCNC Title - About KMotionCNC)
#2 - please attach your Kinematics.txt file
Regards,

Tom Kerekes
Dynomotion, Inc.

Igor
Posts: 60
Joined: Wed Dec 25, 2019 11:37 am

Re: RTCP 5 axis machine

Post by Igor » Fri Jan 10, 2020 7:43 pm

KMotionCNC 435b/
Attachments
Kinematics.txt
(77 Bytes) Downloaded 125 times

User avatar
TomKerekes
Posts: 2527
Joined: Mon Dec 04, 2017 1:49 am

Re: RTCP 5 axis machine

Post by TomKerekes » Sat Jan 11, 2020 2:05 am

Hi Igor,

Strange I tried it on 2 computers and it runs ok here.

It should actually be KMotionCNC 4.35b not KMotion 435b/

But I assume that was just a typo.

I asked previously if the size of the download was correct and I didn't see an answer. Please post the properties of the downloaded file for us to check.

You might try a fresh install of KMotionCNC 4.35b to another computer, copy in the patch, and test to see if that works.
Regards,

Tom Kerekes
Dynomotion, Inc.

Igor
Posts: 60
Joined: Wed Dec 25, 2019 11:37 am

Re: RTCP 5 axis machine

Post by Igor » Sat Jan 11, 2020 7:57 am

Okay, I 'll try another version now. (((( downloaded established. As soon as I add the GCodeInterpreter .dll file - the program closes at startup "
Attachments
GCodeInterpreter .dll
(3.4 MiB) Downloaded 103 times
CNC4.PNG
CNC 3.PNG
CNC 3.PNG (2.87 KiB) Viewed 2339 times

User avatar
TomKerekes
Posts: 2527
Joined: Mon Dec 04, 2017 1:49 am

Re: RTCP 5 axis machine

Post by TomKerekes » Sat Jan 11, 2020 4:37 pm

Hi Igor,

Somehow you put a space in the filename. It should be "GCodeInterpreter.dll" not "GCodeInterpreter .dll"

I downloaded your attached GCodeInterpreter .dll took out the space and it worked for me.
Regards,

Tom Kerekes
Dynomotion, Inc.

Igor
Posts: 60
Joined: Wed Dec 25, 2019 11:37 am

Re: RTCP 5 axis machine

Post by Igor » Sat Jan 11, 2020 5:04 pm

does not work.that 's the problem?
CNC9.PNG
Attachments
CNC8.PNG

Post Reply