See attached photos. The C program is running in thread #3. I see where there are other C programs called by Mcodes and user buttons calling that same thread (#3) but I'm not activating those. I'm just running the G code program until it stops. Is there still some interference there?
AZ
Search found 38 matches
- Tue Jan 21, 2020 12:45 am
- Forum: C Programs
- Topic: C program stops when G code finishes
- Replies: 3
- Views: 1678
- Mon Jan 20, 2020 4:37 pm
- Forum: Noise, Grounding, Shielding Issues
- Topic: Snap Amp Noise affecting USB connection
- Replies: 18
- Views: 7768
Re: Snap Amp Noise affecting USB connection
I installed inductors on all the brushless motor phases, 2 motors , 3 phases. and I have two ferrite cores on the stepper motor wires. These are all installed within 6 inches of the SnapAmp output terminals. The inductors seem to have eliminated the USB comms disconnections due to the servos but it ...
- Mon Jan 20, 2020 4:05 pm
- Forum: C Programs
- Topic: C program stops when G code finishes
- Replies: 3
- Views: 1678
C program stops when G code finishes
Hello, I have a "run forever" C program that starts and runs continuously as long as I don't run a G code program. The C program still runs as long as the G code is running or if I stop the G code with the Cycle Stop button. The C program stops running when the G code finishes running. The portion o...
- Sat Jan 04, 2020 1:14 am
- Forum: Noise, Grounding, Shielding Issues
- Topic: Cross Talk between SnapAmp channels
- Replies: 1
- Views: 1806
Cross Talk between SnapAmp channels
I noticed that current demand on one Snap Amp channel affected the other motor. I have dual Snap Amps with three motors. One Snap Amp has a brushless Servo and an open loop microstepper. The other Snap Amp has a single brushless motor. When the brushless motor on the stepper/servo amp is running slo...
- Mon Dec 23, 2019 5:10 pm
- Forum: Noise, Grounding, Shielding Issues
- Topic: Snap Amp Noise affecting USB connection
- Replies: 18
- Views: 7768
Re: Snap Amp Noise affecting USB connection
Thanks Tom,
I was looking too deep in the documentation, I should have just referred to the first website page and there it is!
AZ
I was looking too deep in the documentation, I should have just referred to the first website page and there it is!
AZ
- Sun Dec 22, 2019 3:37 pm
- Forum: Noise, Grounding, Shielding Issues
- Topic: Snap Amp Noise affecting USB connection
- Replies: 18
- Views: 7768
Re: Snap Amp Noise affecting USB connection
What is the SnapAmp switching frequency?
I'm looking at installing inductors in the motor lines and the ones that look like they'll be best are frequency dependant.
AZ
I'm looking at installing inductors in the motor lines and the ones that look like they'll be best are frequency dependant.
AZ
- Tue Dec 17, 2019 6:45 pm
- Forum: Tuning Servos
- Topic: Smoothing out Brushless motion
- Replies: 11
- Views: 4911
Re: Smoothing out Brushless motion
I had to stay under 1Mb or I got the yellow triangle
AZ
AZ
- Tue Dec 17, 2019 6:43 pm
- Forum: Tuning Servos
- Topic: Smoothing out Brushless motion
- Replies: 11
- Views: 4911
Re: Smoothing out Brushless motion files
Here they are smaller. The attachments worked once I got them below 1 Mb.
AZ
AZ
- Tue Dec 17, 2019 6:00 pm
- Forum: Tuning Servos
- Topic: Smoothing out Brushless motion
- Replies: 11
- Views: 4911
Re: Smoothing out Brushless motion
The files are txt files from the Step function tuning page. There were 4. Each was 1.3 Mb I'll try the cat attachment and another one that I had done previously. There is no GreenCheck, it's a yellow triangle but no explanation. The cat pic worked, Green check and all. I'm going to re do those plots...
- Tue Dec 17, 2019 5:24 pm
- Forum: Tuning Servos
- Topic: Smoothing out Brushless motion
- Replies: 11
- Views: 4911
Re: Smoothing out Brushless motion
I tried attaching in the Config forum and no luck there either. I'll try Previewing in this one. I noticed in the Config forum there was an additional folder called " Polling" next to the Attachments if that means anything to this issue. I tried Preview after doing the Attachments and there was noth...