Search found 51 matches
- Thu Feb 13, 2020 12:10 pm
- Forum: Miscellaneous
- Topic: Push Buttons with LEDs
- Replies: 1
- Views: 2015
Push Buttons with LEDs
Hello, Starting on my mill control panel now and need some info on using momentary push buttons with built in LED. All buttons and LEDs are physical buttons, not KMCNC screen buttons. I have 2 buttons for the Feed Forward and Feed Reverse when Feed Hold is active. I am trying to figure out how to tu...
- Sat Jun 08, 2019 2:30 am
- Forum: Configuration Issues
- Topic: CSS on Lathe
- Replies: 6
- Views: 4116
Re: CSS on Lathe
Hi Tom,
Troy
So its not were i have the encoder connected to on the Kanalog board?On a note unrelated to your problem I believe the KMotionCNC | Tool Setup | Trajectory Planner | Threading | Spindle axis is incorrectly set to 3 instead of 7.
Troy
- Fri Jun 07, 2019 10:24 pm
- Forum: Configuration Issues
- Topic: CSS on Lathe
- Replies: 6
- Views: 4116
Re: CSS on Lathe
Hi Tom, Been trying to get this to work with no change in issue of spindle RPM not changing. So i opened the CSSjogs.c program and enabled the print out. Then did a compile to check it and i got a "CSSJog.c:22: 'persist' undeclared". I get the same persist undeclared when i disable the print out. I ...
- Sun Jun 02, 2019 12:12 pm
- Forum: Configuration Issues
- Topic: CSS on Lathe
- Replies: 6
- Views: 4116
Re: CSS on Lathe
I found one issue, in the MySpindleDefs header file. I had the wrong axis. Had 3 because i was thinking of the spindle encoder is connected to axis 3 inputs. I changed it to 7 which is the output for spindle, but nothing has changed, still does same thing i described in previous post.
Troy
Troy
- Sat Jun 01, 2019 11:50 pm
- Forum: Configuration Issues
- Topic: CSS on Lathe
- Replies: 6
- Views: 4116
CSS on Lathe
Hay Tom, So now iam opening a new can of worms on my lathe. :) And trying to configure for constant surface speed. I have looked at the example...https://dynomotion.com/Help/KMotionCNC/SpindleControl.htm. Altered and added the MySpindleDefs.h to directories DSP_KFLOP and DSP_Kmotion. Below is the al...
- Sat Jun 01, 2019 1:23 am
- Forum: KMotionCNC, G Code Files, Offsets, Post Process
- Topic: Lathe Tool Z offset
- Replies: 13
- Views: 6981
Re: Lathe Tool Z offset
Hi Tom, Well, did some trouble shooting threw the week with no results. So i just tried the good old sanity check and all seems to be working good now:) Step works correctly and so does the M6 pop up code. I think something may have got corrupted when i changed PCs at beginning of retrofit and copie...
- Mon May 27, 2019 3:27 pm
- Forum: KMotionCNC, G Code Files, Offsets, Post Process
- Topic: Lathe Tool Z offset
- Replies: 13
- Views: 6981
Re: Lathe Tool Z offset
Hi Tom, No worries about delay. :) Yes it is still an issue. Currently i have a work around. Iam replacing the M6 with a M0 and executing my M0 c code that does an MDI "M0". Obviously there is no pop up message but at least this way the Gcode will stop for a tool change. Tried your updated ccode and...
- Fri May 24, 2019 11:28 pm
- Forum: KMotionCNC, G Code Files, Offsets, Post Process
- Topic: G83 Lathe
- Replies: 1
- Views: 2756
G83 Lathe
Hello, I am trying to do run a simple spot drill G83 program on my lathe. For some reason iam getting a pop up window when trying to run gcode that states"Y value unspecified in xz plane canned cycle". I have ran this same program a few times a couple days ago with no problems but now it gives me po...
- Mon May 20, 2019 8:56 pm
- Forum: New Feature Request
- Topic: Linux Support
- Replies: 5
- Views: 6360
Re: Linux Support
.... Sorry we don't have the resources to also support Linux. How much would you be willing to pay for a Linux Version? .... Hi Tom, Just some feedback here....If Dynomotion was to make a Linux version, I for one, as an end user for my own machines, would be willing to pay the amount that a license...
- Mon May 20, 2019 1:41 am
- Forum: KMotionCNC, G Code Files, Offsets, Post Process
- Topic: Lathe Tool Z offset
- Replies: 13
- Views: 6981
Re: Lathe Tool Z offset
Hi Tom, Here is screenshots of my ToolSetUp. My main init code and ManualToolChange code. Note that i dont have CSS in my init yet as i have not figured it out yet. The reason for another CycleStart after clicking the OK button is so user does not have to go from keyboard or mouse to machine buttons...