Search found 10 matches

by nice_kflop
Fri Sep 10, 2021 5:03 am
Forum: Configuration Issues
Topic: Stepper Hybrid - JP7 vs JP5
Replies: 15
Views: 1280

Re: Stepper Hybrid - JP7 vs JP5

This drawing is all i found for the driver. Does this mean I use a digital ground pin for ALARM- and use a general purpose 5v tolerant like IO2 for ALARM+, then under limit switch options>>under positive>> i select bit no. 2 Drawing also shows it may need a resistor :? or maybe not! Please correct m...
by nice_kflop
Thu Sep 09, 2021 2:44 am
Forum: Configuration Issues
Topic: Stepper Hybrid - JP7 vs JP5
Replies: 15
Views: 1280

Re: Stepper Hybrid - JP7 vs JP5

:lol: Now that input is set to no input and output is set to CL. Does that mean the encoder is taken into account from the driver and actually being used or no use?
c0.png
c4.png
by nice_kflop
Wed Sep 08, 2021 10:01 pm
Forum: Configuration Issues
Topic: Stepper Hybrid - JP7 vs JP5
Replies: 15
Views: 1280

Re: Stepper Hybrid - JP7 vs JP5

Do I have to adjust encoder into kflop or does the wiring look right
diagram.png
by nice_kflop
Wed Sep 08, 2021 5:42 am
Forum: Configuration Issues
Topic: Stepper Hybrid - JP7 vs JP5
Replies: 15
Views: 1280

Re: Stepper Hybrid - JP7 vs JP5

I read the manual and tried so many configurations, my encoder has 1000 lines and i set the micro stepping drive to 4000 pulse/rev. Do i leave it as is in the image. What changes should I make. - Also,channel 4 has same motor and driver as channel 1 but graph looks much different. Is that because of...
by nice_kflop
Tue Sep 07, 2021 10:32 pm
Forum: Configuration Issues
Topic: Stepper Hybrid - JP7 vs JP5
Replies: 15
Views: 1280

Re: Stepper Hybrid - JP7 vs JP5

Image
by nice_kflop
Tue Sep 07, 2021 9:13 pm
Forum: Configuration Issues
Topic: Axis modes - jog buttons
Replies: 2
Views: 383

Re: Axis modes - jog buttons

Got it to work with closed loop and encoder inputs. Thank you.
by nice_kflop
Tue Sep 07, 2021 9:12 pm
Forum: Configuration Issues
Topic: Stepper Hybrid - JP7 vs JP5
Replies: 15
Views: 1280

Re: Stepper Hybrid - JP7 vs JP5

Hi, yes i wanted to test JP5, just now i got it working on JP5 after your first post here about DefineCoordSystem, all i had to do is ground the other wires from pins 5 to 7 on jp5 and change the DefineCoordSystem. The jog works now. Thank you.
by nice_kflop
Tue Sep 07, 2021 6:05 am
Forum: Configuration Issues
Topic: Stepper Hybrid - JP7 vs JP5
Replies: 15
Views: 1280

Re: Stepper Hybrid - JP7 vs JP5

Hi, Thanks for your reply on DefineCoordSystem. I did change it please take a peak at the code below. I have 3 steppers attached to channels 0 x-axis, ch1 y-axis, and ch4 (assuming its a-axis)...channel 4 does move the stepper on the step response screen....in the axis window, i have 0, 1, and 4 ena...
by nice_kflop
Thu Sep 02, 2021 4:50 am
Forum: Configuration Issues
Topic: Axis modes - jog buttons
Replies: 2
Views: 383

Axis modes - jog buttons

Hi, when my axis mode for the closed loop stepper motor and driver are set to "Input: No input, Output: step Dir" I am able to jog it using the KmotionCNC screen. But when I use "Input: encoder, output: CL step" which is the correct setting, the jog button for x axis doesn't move the stepper. Why is...
by nice_kflop
Wed Sep 01, 2021 2:35 am
Forum: Configuration Issues
Topic: Stepper Hybrid - JP7 vs JP5
Replies: 15
Views: 1280

Stepper Hybrid - JP7 vs JP5

I have successfully been able to move the closed loop stepper motor that uses a hybrid servo drive "HBS860H". When I have it hooked on JP7, i am able to move the motor by the kmotion "step response" screen and from the "kmotionCNC" jog buttons. But, when I use the JP5, I am only able to move the ste...