Search found 50 matches

by Scott Pancheau
Tue Feb 06, 2024 4:45 pm
Forum: Configuration Issues
Topic: Filter screens and analog screen problems.
Replies: 2
Views: 68

Re: Filter screens and analog screen problems.

Thanks Tom, You might remember I am not very good at this part of the use. I will let you know if I am successful.
Thanks,
Scott
by Scott Pancheau
Sun Feb 04, 2024 10:05 pm
Forum: Configuration Issues
Topic: Filter screens and analog screen problems.
Replies: 2
Views: 68

Filter screens and analog screen problems.

I had a computer crash of some sort on my lathe where my VGA port went out. Some of the parameters seem to have been affected. Initially after this I would get a message that if I tried to continue to the dynomotion console screen the 435b woud be lost. I took the computer to the tech shop. They sai...
by Scott Pancheau
Tue Feb 14, 2023 5:53 pm
Forum: C Programs
Topic: INSTALL POST PROCESSOR
Replies: 2
Views: 591

Re: INSTALL POST PROCESSOR

Thanks for your quick reply Tom. I will message them.
by Scott Pancheau
Tue Feb 14, 2023 4:33 pm
Forum: C Programs
Topic: INSTALL POST PROCESSOR
Replies: 2
Views: 591

INSTALL POST PROCESSOR

Hi Tom,
I found a turning post in your help information for Fusion 360. I want to install the post without messing up the existing programming. I am pretty elementary , so hoping you can give me the specific steps to do so.
Thank You,
Scott
by Scott Pancheau
Thu Mar 10, 2022 7:21 pm
Forum: KMotionCNC, G Code Files, Offsets, Post Process
Topic: Tool offsets for lathe
Replies: 2
Views: 1099

Tool offsets for lathe

My lathe tool offsets has X and Y as the offsets to set. How do I change the Y column to be Z and therefore affect the Z offset amount.
Thanks,
Scott
by Scott Pancheau
Thu Jan 27, 2022 3:53 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 2266

Re: Changed C program?

I could do this morning if still available Tom. If not then the Monday date / time would work as well. My email is spancheau@gmail.com

Thanks,
Scott
by Scott Pancheau
Wed Jan 26, 2022 2:41 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 2266

Re: Changed C program?

Hi Tom, I went back and changed the output gain to -1. That changed the response when spindle is enabled to the spindle hunting back and forth positive voltage , negative voltage outputs with spindle rotating CW, CCW in response. This just continues until the disable is pushed. Went to kmotion to se...
by Scott Pancheau
Mon Jan 24, 2022 4:06 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 2266

Re: Changed C program?

Hi Tom, I reversed the output gain from 1 to 0. Got the same result. As soon as I enable kmotion the spindle takes off. I have the snap amp installed with the correct 80 volt max power supply for the X axis that would not tune when we last got together on it. I would like to set a time for you to ge...
by Scott Pancheau
Thu Jan 20, 2022 10:17 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 2266

Re: Changed C program?

Hi Tom, Your item #1 import into kmotion. Just want to make sure I did this right. I opened the channel setup screen, input chanel 4 at top,then with the C program open I pressed the import all from open program. I got the 3 axis found message 0,1, and 4 . Pressed the import all from open C. If that...