Search found 46 matches

by Scott Pancheau
Thu Mar 10, 2022 7:21 pm
Forum: KMotionCNC, G Code Files, Offsets, Post Process
Topic: Tool offsets for lathe
Replies: 2
Views: 301

Tool offsets for lathe

My lathe tool offsets has X and Y as the offsets to set. How do I change the Y column to be Z and therefore affect the Z offset amount.
Thanks,
Scott
by Scott Pancheau
Thu Jan 27, 2022 3:53 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 1226

Re: Changed C program?

I could do this morning if still available Tom. If not then the Monday date / time would work as well. My email is spancheau@gmail.com

Thanks,
Scott
by Scott Pancheau
Wed Jan 26, 2022 2:41 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 1226

Re: Changed C program?

Hi Tom, I went back and changed the output gain to -1. That changed the response when spindle is enabled to the spindle hunting back and forth positive voltage , negative voltage outputs with spindle rotating CW, CCW in response. This just continues until the disable is pushed. Went to kmotion to se...
by Scott Pancheau
Mon Jan 24, 2022 4:06 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 1226

Re: Changed C program?

Hi Tom, I reversed the output gain from 1 to 0. Got the same result. As soon as I enable kmotion the spindle takes off. I have the snap amp installed with the correct 80 volt max power supply for the X axis that would not tune when we last got together on it. I would like to set a time for you to ge...
by Scott Pancheau
Thu Jan 20, 2022 10:17 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 1226

Re: Changed C program?

Hi Tom, Your item #1 import into kmotion. Just want to make sure I did this right. I opened the channel setup screen, input chanel 4 at top,then with the C program open I pressed the import all from open program. I got the 3 axis found message 0,1, and 4 . Pressed the import all from open C. If that...
by Scott Pancheau
Tue Jan 18, 2022 5:22 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 1226

Re: Changed C program?

Hi Tom, I know you have to respond to many questions every day and thus you probably would not remember, but my second post in this exchange says the same thing about the spindle. It worked after you tuned it up when you had control of the computer. Now it does not and I have not messed with any of ...
by Scott Pancheau
Mon Jan 17, 2022 6:43 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 1226

Re: Changed C program?

Hi Tom, I did try the download, initialize, and run function for the TK C program. It showed no errors, but the results trying to operate the spindle did not change. Jog commands would not work and if I try to initialize kmotion the spindle trys to go full speed as soon as I do. I got a cable for th...
by Scott Pancheau
Wed Jan 12, 2022 1:46 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 1226

Re: Changed C program?

Thanks Tom, Changing the subject this time. I recieved the snap amp and have it installed. Have a couple of questions. 1. Do I have to move the encoder inputs from the kanalog to the snap amp? 2 If so do you offer the 25 pin cable needed to do so and a breakout board to connect to? 3 Will the curren...
by Scott Pancheau
Mon Jan 10, 2022 5:47 pm
Forum: Configuration Issues
Topic: Changed C program?
Replies: 18
Views: 1226

Re: Changed C program?

Thanks Tom,
There is no response of movement for the spindle with jog command. The console shows no error message ( see picture). Dac commands still work,
but not jog. I do not know what you mean by show C program code. Is this under the sub program - spindle jog or?
Thanks,
Scott