Search found 16 matches

by Mateusz
Wed Aug 28, 2019 9:07 pm
Forum: C Programs
Topic: Rotary tool changer
Replies: 11
Views: 1538

Re: Rotary tool changer

Hello Tom, It took few months rather few days from my last post, but now I've got to back to work. Machine was running all the time without tool changer... :D Any way, I fixed a turret calculation task to compute movement. I hope now is fine. Right now I would't care on tasks time-out procedure. Thi...
by Mateusz
Sun Jun 16, 2019 7:54 pm
Forum: Miscellaneous
Topic: Rigid Taping - DAC closed loop Spindle
Replies: 1
Views: 806

Rigid Taping - DAC closed loop Spindle

Hello Tom, I'm very eager to give a go with Rigid Tap functionality. I went thru different forums and still is something missing. Starting from beginning, - I found this Patch KiT https://dynomotion.com/Software/Patch/AddG84RigidTapV434h/ .DO I have to replace some of the files in GCodeInterpeter Ca...
by Mateusz
Sun Jun 16, 2019 6:53 pm
Forum: Miscellaneous
Topic: Spindle DAC - no read out of spindle rate
Replies: 7
Views: 1590

Re: Spindle DAC - no read out of spindle rate

Hi Tom, I sticked an input with "while(VFD_IN);" command just after SetBit(SPINDLECW_BIT), It is running, but I'm nut sure I've made it correctly :) My next step is to introduce Rigid Tap and I'm not sure this change will influence a TAP cycle...I've got few question on this but I'll rise them on di...
by Mateusz
Fri Jun 14, 2019 8:40 pm
Forum: Miscellaneous
Topic: Spindle DAC - no read out of spindle rate
Replies: 7
Views: 1590

Re: Spindle DAC - no read out of spindle rate

Another thing, I've got extra signal from Spindle VFD which says "I'm reached set speed'' (Speed Coincidence Signal). May I use it with command M3 ? to make sure spindle has declared RPM.....

Thanks
Mateusz
by Mateusz
Fri Jun 14, 2019 8:30 pm
Forum: C Programs
Topic: KFLOP STOP and logic outputs to control amplifiers
Replies: 2
Views: 871

Re: KFLOP STOP and logic outputs to control amplifiers

Works - of course
silly question....I've been fixed to much doing Initialisation on thread 1.....https://dynomotion.com/Help/Multitasking.htm
by Mateusz
Fri Jun 14, 2019 8:00 am
Forum: Miscellaneous
Topic: Spindle DAC - no read out of spindle rate
Replies: 7
Views: 1590

Re: Spindle DAC - no read out of spindle rate

Hello Tom,

Good point ! I did configured but rather placing axis 3 I placed number 4, this should resolve an issue, Tomorrow I'm going to see my 11 tons beast.


Thank you !
by Mateusz
Thu Jun 13, 2019 10:33 pm
Forum: Miscellaneous
Topic: Spindle DAC - no read out of spindle rate
Replies: 7
Views: 1590

Re: Spindle DAC - no read out of spindle rate

I will add , that I'm using encoder feedback on spindle on axis 3 these are my definitions: #define SPINDLEAXIS 3 // Axis Channel to Jog to rotate Spindle #define FACTOR (3413.333333/60.0) // to convert RPM to counts/sec (counts/rev / 60.0sec) #define SPINDLECW_BIT 147 // bit to activate to cause CW...
by Mateusz
Thu Jun 13, 2019 10:29 pm
Forum: C Programs
Topic: Rotary tool changer
Replies: 11
Views: 1538

Re: Rotary tool changer

Tom,

I'll get back to this topic in few days, I'm running out my time. Once I'll collect all information and fix the charts, I will present them to you.

Thanks
by Mateusz
Thu Jun 13, 2019 10:26 pm
Forum: C Programs
Topic: KFLOP STOP and logic outputs to control amplifiers
Replies: 2
Views: 871

KFLOP STOP and logic outputs to control amplifiers

Hi Tom Another issue I don't know how to overcome, I remember I saw on old forum similar problem, but I can not find it any more. I'm using watchdog on thread 7, and when I hit ESC button on keyboard or press STOP / abort all motion on the KmotionCNC screen. KFLOP goes to stop mode. All threads are ...
by Mateusz
Thu Jun 13, 2019 10:24 am
Forum: Custom Screens, KMotionCNC Screen Editor
Topic: KMotionCNC Translation
Replies: 3
Views: 918

Re: KMotionCNC Translation

Hi Tom,

Yes, I know Screen Editor, I did play with it. I have to translate toolbar and other buttons etc...link what you send me should do a job :)
by the way I should be able to change decimal point accuracy on DRO-s as well ?

Thank you