Search found 11 matches

by Lafayette
Tue Feb 13, 2018 8:00 pm
Forum: Hardware Interface Issues
Topic: Help! PWM 0-10V.
Replies: 22
Views: 17780

Re: Help! PWM 0-10V.

Pin 26 is connected to the converter that led you higher, it will be controlled by the speed 0-10V.
by Lafayette
Tue Feb 13, 2018 7:59 pm
Forum: Hardware Interface Issues
Topic: Help! PWM 0-10V.
Replies: 22
Views: 17780

Re: Help! PWM 0-10V.

I will connect the optopar to the flap, and from it I will connect to the servo amplifier at the input of the work permit(S-ON).
by Lafayette
Tue Feb 13, 2018 7:56 pm
Forum: Hardware Interface Issues
Topic: Help! PWM 0-10V.
Replies: 22
Views: 17780

Re: Help! PWM 0-10V.

Lafayette wrote:
Tue Feb 13, 2018 7:54 pm
Post by Lafayette » Mon Feb 12, 2018 9:21 am

I want to use to adjust the spindle speed
JP6 IO26 Gen Purpose PWM0 out
I want to use to turn the spindle on and off.
JP6 IO27 Gen Purpose LVTTL I/O 3.3V
I'm sorry, I was a little mistaken.
by Lafayette
Tue Feb 13, 2018 7:54 pm
Forum: Hardware Interface Issues
Topic: Help! PWM 0-10V.
Replies: 22
Views: 17780

Re: Help! PWM 0-10V.

Post by Lafayette » Mon Feb 12, 2018 9:21 am

I want to use to adjust the spindle speed
JP6 IO26 Gen Purpose PWM0 out
I want to use to turn the spindle on and off.
JP6 IO27 Gen Purpose LVTTL I/O 3.3V
by Lafayette
Tue Feb 13, 2018 7:09 pm
Forum: Hardware Interface Issues
Topic: Help! PWM 0-10V.
Replies: 22
Views: 17780

Re: Help! PWM 0-10V.

The optocoupler will only work to enable the servo amplifier.
by Lafayette
Tue Feb 13, 2018 7:06 pm
Forum: Hardware Interface Issues
Topic: Help! PWM 0-10V.
Replies: 22
Views: 17780

Re: Help! PWM 0-10V.

I have a servo amplifier AEROTECH BA20-160.
I want that from one pin 26 the authorization of the servo amplifier should be given, and from the other 27 the speed change through.
The maximum speed is 5647.
I'm interested in stability at low speed.
by Lafayette
Tue Feb 13, 2018 8:40 am
Forum: Hardware Interface Issues
Topic: Help! PWM 0-10V.
Replies: 22
Views: 17780

Re: Help! PWM 0-10V.

I will turn on and off through the standard M code.
IO27 will be connected to the optocoupler, and it will command the servo amplifier S-ON/S-OFF
I do not understand why I need an analog output 5V. when it needs 0-10V.
And how you can change the spindle speed.
by Lafayette
Mon Feb 12, 2018 6:21 am
Forum: Hardware Interface Issues
Topic: Help! PWM 0-10V.
Replies: 22
Views: 17780

Re: Help! PWM 0-10V.

I want to use to adjust the spindle speed JP6 IO26 Gen Purpose PWM0 out I want to use to turn the spindle on and off. JP6 IO27 Gen Purpose LVTTL I/O 3.3V Specification of the converter: input3.3V Level0-100% PWM Signal, output0-10V Voltage PWM Signal receiving frequency range:suggested 1KHZ-3KHZ The...
by Lafayette
Fri Feb 09, 2018 7:56 am
Forum: Hardware Interface Issues
Topic: Help! PWM 0-10V.
Replies: 22
Views: 17780

Re: Help! PWM 0-10V.

PWM conversion board in 0-10V
by Lafayette
Fri Feb 09, 2018 4:41 am
Forum: Hardware Interface Issues
Topic: Help! PWM 0-10V.
Replies: 22
Views: 17780

Help! PWM 0-10V.

Hello! I'm collecting the machine. I will connect the encoders, so I decided to buy KFLOP. The axles are controlled by step/dir. Spindle with analog control. I bought a PWM conversion board in 0-10V. (a photo). If I still understand in the electrician and can disconnect the wiring, then in programmi...